Video: Painting Rooms With High Humidity
Surfaces in rooms with high humidity must withstand exposure to water and detergents. It is necessary to protect such rooms from the appearance of mold and paint them so that they are easy to wash and wipe.
Remember:
-The standard for wet rooms is divided into two classes: VN (waterproof surfaces) and VO (water-repellent surfaces).
-VN paint class is used for walls washed with water, or for walls where splashing or leakage is possible. Areas where joints, joints and pipes pass through walls must be waterproof.
-Examples of using the HV system: walls from floor to ceiling, in areas where bathtubs and showers are located, as well as walls located at a distance of 1 m from the above walls, if these walls are not protected by a dividing waterproof wall; on walls where water may leak from the tap connections.
-VO paint class is used on walls where splashing, wet cleaning, condensation or high humidity is possible.
-Examples of using the VO system: walls in rooms for washing; walls located at a distance of 0.5 m from sinks in the kitchen or in the laundry room; walls in bathrooms and showers located at a distance of more than 1 m from the bath or shower area, if these walls are not protected by a dividing waterproof partition; walls at a distance of 0.5 m from sinks and toilets; ceilings in bathrooms, showers and similar rooms.
Water-repellent systems (WR) in kitchens, laundry rooms and other similar areas. New unfinished walls made of plasterboard, fibreboard or sheathing.
Instructions:
1. Drive in all nail heads and fill in any uneven areas or holes with lightweight filler or wet room filler. Use glue or putty to glue the fiberglass strips to all joints.
2. Fill all joints and cracks with filler. Let it dry.
3. If required, apply another coat of putty to cracks, joints and nail heads.
4. Sand the filled areas with sandpaper, and then sweep away dust from them.
If you paint with wet room primer, use protective gloves as this primer is difficult to remove when dry.
5A. When painting walls without a textured finish: first paint the surface with a wet room primer. Then, roller apply two coats of wet room paint or semi-gloss latex emulsion paint.
5 B. When painting textured walls: The textured wall covering is primed with wet room primer or semi-gloss latex emulsion paint. Let the first layer dry before applying the second.
Attention:
Do not use the same roller for wet room primer and wet room paint as this may cause discoloration.
Watertight system (VH) in bathrooms and similar wet areas. New walls made of plasterboard, fibreboard or sheathing.
1. When painting with wet room primer, use protective gloves as this primer is difficult to remove when dry.
2. Drive in all nail heads and fill in any uneven areas or holes with lightweight filler or wet room filler. Let the putty dry.
3. If required, apply another coat of putty to cracks, joints and nail heads.
4. Sand the putty areas with sandpaper, and then sweep away dust from them.
5. When painting textured walls: prime the surface with wet room primer diluted with an equal part of water (1: 1). Wallpaper in a damp room is glued to the wall with undiluted primer.
6. Apply another layer to the wall with a roller. Let each layer dry before overlaying the next.
7. Apply two coats of wet room paint with a roller.
Water-repellent systems (WR) in kitchens, laundry rooms and other similar areas. Walls pre-painted and wallpapered.
Instructions:
1. Wear protective gloves. Cover the floor with plastic or paper. Cover plinths and skirting boards with plastic or paper and secure with adhesive tape.
2. Thoroughly rinse the walls with a degreasing agent and detergent. Wear protective gloves. Rinse the walls thoroughly. Wipe the wallpaper-covered walls with denatured alcohol. Remove any loose wallpaper and wall material.
3. If the surface has a rough structure (embossing), you can putty the entire wall with a wet cement putty. Fill all damaged areas and cracks with a lightweight filler. When it's dry, sand the bumps with sandpaper.
4A. Prime the wall with wet room primer. Then use a roller to apply two coats of wet room paint or semi-gloss latex emulsion paint.
4B. When painting textured walls: Apply glue to the fiberglass cloth. Then apply two coats of wet room paint with a roller. Let each layer dry before overlaying the next.
Maintenance instructions:
- In the first days, the painted surfaces should be handled with care: let the surface dry for at least a week before using it or sprinkling it with hot water.
- Washing, as a rule, is carried out with conventional synthetic detergents, from which peeling occurs, as they can damage the surface. Do not use alcoholic solutions (eg denatured alcohol) or strong solvents (eg white spirit), as these may dissolve the paint. Learn to flush the walls from floor to ceiling. Rinse the surface with clean water and dry it.
- Walls should be regularly cleaned of lime deposits, soap and similar deposits. This is especially important for areas subject to such stress, such as showers and areas under the sink and tub. The sides and cut of the tub must be removed to clean the floor and walls. Use a soft brush and a descaling solution when cleaning. Rinse the surface with clean water and dry it.
- If stains cannot be removed with synthetic detergents, try white spirit, it has a whitening effect and can be a good stain remover or mildew stain remover.
- Check if there is sufficient ventilation and if it works well. Learn to use a rubber roller (dehumidifier) to remove water from the floor. Draw your shower curtain and open the door a little. This will help reduce the humidity in the room and prevent mold from forming.
- Check that the insulation around the pipes is intact and that all screw holes are properly sealed. Always seal the screw holes and other holes as soon as they are made.
